DownloadBedini energizer building manual pdf. Free Download 8 42 a. When ready, you should get a confirmation. Travis Outlaw – Amnesty Clause hey, my. REPLICATE THE BEDINI RADIANT CHARGING PHENOMENON .. BUILDING THE FRAME. UPDATED COIL WINDING INSTRUCTIONS BY LEE. . list of materials required to replicate the Bedini School Girl energizer. and testing the Bedini Monopole Mechanical Oscillator Energizer with Simplified that the beginner reads this manually thoroughly before starting to build.
|Published (Last):||25 February 2015|
|PDF File Size:||12.1 Mb|
|ePub File Size:||20.6 Mb|
|Price:||Free* [*Free Regsitration Required]|
The next four screws are for the four negative legs of the coil windings. Skateboard bearings are 7mm inner diameter.
See the picture below. Ifthe magnet instantly jumps away from the coil you manuap the right polarity. But if the batteries have different voltages to startthen the battery with the lower voltage will charge up and then when the lower and higherare the same they will finish charging together.
To determine which is north just place one flat side towards north and if it byilding then stopit and face the other side towards north and it should stay with that side facing north. They sell it in about 10 pound spools. They will just be loose on the Plexiglas. Both are areal plus for the system.
The positive is on the left and the negative on the right. This guide is to help those who haveaverage skills with average tools to build this extraordinary device for themselves.
They are quite strong so use caution not to pinch your fingers as they closetogether. Thetwo energizzer on the right are for the trigger winding.
The bottom plate, 2 shaft supports, and 2coil blocks.
This is actually a 12 coil in progress since I placed 2 setsof double stacked magnets and will put another 6 coils on the back.
Now that the wires are twisted start winding it on the spool clockwise from oneend, but leave about 10 inches of wire not wound on the spool so you can connect it energizzer switching circuit. We have tried to include all the information needed in this document to tell youwhere to buy the parts, how to put them together and start gaining first hand experiencewith radiant technology.
With 4 magnets they will each be90 degrees apart and 5 magnets 72 degrees and 6 magnets is 60 degrees apart. You will need to have access to, and be able to use, the following tools: The rotor pictured above has 6 magnets,double stacked. Connecting the coil to the circuit: So be careful not to connect the negativeoutput to the negative input or your input battery will melt your wires and waste a lot ofpower. Scrape all theway around. For the input power insert enerigzer 18 AWG or smaller still big enough to handle the 2to 3 amps current you may need wire into the wire connectors shown as 4 on thediagram.
No need to reverse thedrill direction. You may even have to slapit a couple times to get it going fast enough at first.
The base is made from 5 pieces of wood. Oneside is black and the other is metal and is electrically connected to the collector. Here is a picture. Remember itis energizee that the system not be turning without having place for the radiant bwdini go! Place a magnet with the north pole side facing the core on the part of the core thatprotrudes out. Try to have the winding end at the same end the other wires are sticking out.
The holeclosest to the end will be on the side facing the rotor. The systemis fed by conventional electricity from a battery or builing power supply plugged into the wall. Nothing is doctored it is all just as descirbed. But if you accidentally connect thepositive directly to the negative the current will get any wire dangerously hotimmediately.
Bedini-Energizer-Building-Manual Pages 1 – 32 – Text Version | FlipHTML5
The speed of the rotor increases substantially with each coil. For those who are notfamiliar with schematics the next page has the parts list of the components and othervaluable information. There is very little current and no heating involved. Take the coil and place this spaceron the protruding part of the ferrite core. It makes no difference which one is where. When you have put enough of the rods in, they will all be tight and will notfall out.
The spinning counterclockwise if it starts will gain speed and only stop when the threadis wound tight.